Thermal and Mechanical Performance of Ultra-high-performance Basalt Fiber Concrete Incorporating Nano Agricultural Waste Additives at Ambient and Elevated Temperatures
J. Environ. Nanotechnol., Volume 15, No 1 (March 2026) pp. 270-285
Abstract
This study explored the development of sustainable ultra-high-performance basalt fiber high-strength concrete (UHPBF-HSC) using agricultural waste materials. Nano-sugarcane bagasse ash (NSCBA), nano cotton straw ash (NCSA), and nano rice straw ash (NRSA) were incorporated as partial cement replacements. Additionally, basalt fiber (1.5%), silica fume (10%), and superplasticizer (0.5%) were consistently included in all mixes. The nanoparticles were produced through mechanical processing and heat treatment. Four dosage levels (5-20% by weight of cement replacement) were tested in combination with basalt fibers. The study evaluated the effects of elevated temperatures (300℃ and 600℃) on UHPBF-HSC, focusing on compressive strength (CS), strength degradation, mass loss, ultrasonic pulse velocity, splitting tensile strength (STS), flexural strength (FS), and water absorption. Results indicated that increasing nanoparticle dosage generally enhanced mechanical properties. Among all mixes, the NSCBA4 (M4) mix exhibited superior performance, achieving approximately 9.7% and 23.0% higher CS than the corresponding NCSA4 and NRSA4 mixes, respectively, at identical replacement levels, in addition to outperforming conventional concrete. The mixes NCSA and NRSA showed similar performance but were less effective than NSCBA. Scanning electronic microscopic analysis revealed well-bonded matrices and compacted sections under normal conditions. However, elevated temperatures led to microcrack formation due to ettringite decomposition and water evaporation. A comparative analysis and prediction of STS and FS were conducted using various codes and literature sources.
Full Text
Reference
Abbas, A. A. H., Kharun, M. and Chiadighikaobi, P. C., The effect of minibars basalt fiber fraction on mechanical properties of high-performance concrete, Cogent Eng., 9(1), 2136603(2022).
https://doi.org/10.1080/23311916.2022.2136603
Abid, M., Waqar, G. Q., Mao, J., Javed, M. F. and Almujibah, H., Mechanical properties, microstructure and GEP-based modeling of basalt fiber reinforced lightweight high-strength concrete containing SCMs, J. Build. Eng., 96, 110378(2024).
https://doi.org/10.1016/j.jobe.2024.110378
ACI Committee 318, Building Code Requirements for Structural Concrete (ACI 318-99) and Commentary, 318R-99, American Concrete Institute, Farmington Hills (1999).
https://ia600409.us.archive.org/26/items/1.ACI31899/1.%20ACI%20-318-99.pdf
ACI Committee 363, State-of-the-Art Report on Highstrength Concrete, ACI 363R-92, American Concrete Institute, Farmington Hills (1997).
https://www.silicafume.org/pdf/reprints-363rtoc.pdf
Ahmed, M., Dad, K. M. K. and Wamiq, M., Effect of concrete cracking on the lateral response of RCC buildings, Asian J. Civ. Eng. Build. Housing, 9 (1), 25e34(2008).
Almohammed, F., Thakur, M. S., Lee, D., Kumar, R. and Singh, T., Flexural and split tensile strength of concrete with basalt fiber: An experimental and computational analysis, Construct. Build. Mater., 414, 134936(2024).
https://doi.org/10.1016/j.conbuildmat.2024.134936
Alomayri, T. and Ali, B., Effect of plant fiber type and content on the strength and durability performance of high-strength concrete, Constr. Build. Mater., 394, 132166(2023).
https://doi.org/10.1016/j.conbuildmat.2023.132166
Althoey, F., Zaid, O., Alsulamy, S., Martínez-García, R., de Prado-Gil, J. and Arbili, M. M., Experimental study on the properties of ultra-high-strength geopolymer concrete with polypropylene fibers and nano-silica, Plos one, 18(4), e0282435(2023).
https://doi.org/10.1371/journal.pone.0282435
Amin, M., Zeyad, A. M., Tayeh, B. A. and Agwa, I. S., Effects of nano cotton stalk and palm leaf ashes on ultrahigh-performance concrete properties incorporating recycled concrete aggregates, Constr. Build. Mater., 302, 124196(2021).
https://doi.org/10.1016/j.conbuildmat.2021.124196
An, F. C., The Effects of Different Constitutive Compression Models of Concrete on the FRP–Concrete Bonded Interface, Int. J. Polym. Sci., 2025(1), 7722361(2025).
https://doi.org/10.1155/ijps/7722361
Anish, V. and Logeshwari, J., A review on ultra-high-performancefibre-reinforced concrete with nanomaterials and its applications, J. Eng. Appl. Sci., 71(1), 25(2024).
https://doi.org/10.1186/s44147-023-00357-8
Batool, F., Masood, A. and Ali, M., Characterization of sugarcane bagasse ash as pozzolan and influence on concrete properties, Arab. J. Sci. Eng., 45(5), 3891-3900(2020).
https://doi.org/10.1007/s13369-019-04301-y
Berktaş, İlayda., Facile synthesis of graphite-and graphene-based hybrid additives by silanization and effects of these additives on the thermal conductivity of cementitious grouts used in shallow geothermal systems, PhD diss., (2020).
https://research.sabanciuniv.edu/id/eprint/41491
Carino, N. J. and Lew, H. S., Re-examination of the relation between splitting tensile and compressive strength of normal weight concrete, ACI J. Proce., 79 (3), 214e219(1982).
https://doi.org/10.14359/10900
Chen, W. F. and Robert, L. Y., Tensile strength of concrete: Double-punch test., J. Struc. Division, 106 (8), 1673-1693(1980).
https://doi.org/10.1061/JSDEAG.0005493
Du Beton, C. E. I., CEB-FIP Model Code 2010; CEB-FIP: Lausanne, Switzerland, (2012).
https://site.abece.com.br/wp-content/uploads/2023/09/fib_Bull65_NMG.pdf
Du, B., Xu, F., AlAteah, A. H. and Mostafa, S. A., Sustainable development of ultra high-performance concrete using basil plant waste: Investigation at normal and extreme conditions, J. Build. Eng., 80, 107997(2023).
https://doi.org/10.1016/j.jobe.2023.107997
El Berdai, Y., Taha, Y., Safhi, A. M., Trauchessec, R., Hakkou, R. and Benzaazoua, M., How Does Coarse Aggregate Type Influence Mechanical Properties of High-Strength Concrete?, ACI Mater. J., 122(3), 79-87(2025).
https://doi.org/10.14359/51746716
Eme, D. B. and Nwaobakata, C., Effect of water cement ratio variation and coarse aggregate gradation on the compressive strength of cement concrete, Int. Res. J. Adv. Eng. Sci., 4(1), 115-122(2019).
http://irjaes.com/wp-content/uploads/2020/10/IRJAES-V4N1P57Y18.pdf
GB 50010-2010; Chinese Standard Code for Design of Concrete Structures, MOHURD: Beijing, China, (2015).
https://doi.org/10.1155/ijps/7722361
Huang, K., Xie, J., Wang, R., Feng, Y. and Rao, R., Effects of the combined usage of nanomaterials and steel fibres on the workability, compressive strength, and microstructure of ultra-high-performance concrete, Nanotechnol. Rev., 10(1), 304-317(2021).
https://doi.org/10.1515/ntrev-2021-0029
Hussain, L. N., Hamood, M. J. and Al-Shaarbaf, E. A., Behavior of ultra-high-performance concrete deep beams reinforced by basalt fibers, Open Eng., 14(1), 20240019 (2024).
https://doi.org/10.1515/eng-2024-0019
IS – 456: 2000; Plain Concrete and Reinforced, Bureau of Indian Standards: New Delhi, India, (2000).
https://law.resource.org/pub/in/bis/S03/is.456.2000.pdf
Khan, M. M. and Iqbal, M. A., Strain rate and size effects on dynamic tensile behaviour of standard and high-strength concrete: an experimental study, Struc., 63, 106325(2024).
https://doi.org/10.1016/j.istruc.2024.106325
Legeron, F. and Paultre, P., Prediction of modulus of rupture of concrete, ACI Mater. J. 97 (2), 193e200(2000).
Mostafa, S. A., Bassam A. T. and Ibrahim, A., Investigation the properties of sustainable ultra-high-performance basalt fibre self-compacting concrete incorporating nano agricultural waste under normal and elevated temperatures, Case Stud. Constr. Mater., 17, e01453(2022).
https://doi.org/10.1016/j.cscm.2022.e01453
Muniyasamy, M. K. and Dinesh, K. M., Analyzing the Characteristics of Self-Compacting, Basalt Fiber, Ultra-High-Performance Concrete Using Nanowaste Product at Both High and Normal Temperature Changes, Int. Conf. Civ. Eng. Innov. Develop. Eng. Adv., 387, 21-30(2023).
https://doi.org/10.1007/978-981-99-6175-7_3
Nasser, I. M., Ibrahim, M. H. W., Zuki, S. S. M., Algaifi, H. A. and Alshalif, A. F., The effect of nanosilica incorporation on the mechanical properties of concrete exposed to elevated temperature: a review, Environ. Sci. Pollut. Res., 29(11), 15318-15336(2022).
https://doi.org/10.1007/s11356-021-18310-8
Oluokun, F. A., Burdette, E. G. and Deatherage, J. H., Splitting tensile strength and compressive strength relationships at early ages, ACI Mater. J., 88 (2), 115-121(1991).
Perera, M. A. G. P. and Ranjith, P. G., Eco-friendly cementitious composites for enhanced strength: Emerging trends and innovations, J. Clean. Prod., 468, 142962(2024).
https://doi.org/10.1016/j.jclepro.2024.142962
Saha, A., Tonmoy, T. M., Sobuz, M. H. R., Aditto, F. S. and Mansour, W., Assessment of mechanical, durability and microstructural performance of sulphate-resisting cement concrete over portland cement in the presence of salinity, Constr. Build. Mater., 420, 135527(2024).
https://doi.org/10.1016/j.conbuildmat.2024.135527
Shi, C., Wu, Z. and Banthia, N., Ultra-high-performance concrete, Des. Perf. appli., 504(2024).
https://doi.org/10.1201/9781003203605
Sun, T., Wang, X., Ashour, A. and Han, B., 16-Sustainable ultra-high-performance concrete materials and structures, Sustain. Concre. Mater. Struct., 487-529(2024).
https://doi.org/10.1016/B978-0-443-15672-4.00016-4
Supit, S. W., Nishiwaki, T., Shaikh, F. U., Boonserm, K. and Rahman, S. A., Influences of hybrid fiber-reinforcement using wollastonite and cellulose nanofibers on strength and microstructure characterization of ultra-high-performance mortar, Constr. Build. Mater., 423, 135802(2024).
https://doi.org/10.1016/j.conbuildmat.2024.135802
Tran, H. B., Le, V. B. and Phan, V. T. A., Mechanical properties of high strength concrete containing nano SiO2 made from rice husk ash in southern Vietnam, Cryst., 11(8), 932(2021).
https://doi.org/10.3390/cryst11080932
Ubayi, S. M., Mathur, C. V., Abubakar, B. S. and Idris, H. I., Rice Husk Ash in Concrete: A Review of Cement Replacement Proportions and Mechanical Properties, Int. J. Eng. Sci., 1(5), 1-15(2024).
https://doi.org/10.5281/zenodo.13888854
Ünal, M. T., Hashim, H. B., Gökçe, H. S., Ayough, P., Köksal, F., El-Shafie, A., Osman, S. and Pordesari, A., Development and Characterization of Basalt Fiber-Reinforced Green Concrete Utilizing Coconut Shell Aggregates, Sustain., 16(17), 7306(2024).
https://doi.org/10.3390/su16177306
Ünal, M. T., Gökçe, H. S., Ayough, P., Alnahhal, A. M., Şimşek, O. S. M. A. N. and Nehdi, M. L., Nanomaterial and fiber-reinforced sustainable geopolymers: A systematic critical review, Constr. Build. Mater., 404, 133325(2023).
https://doi.org/10.1016/j.conbuildmat.2023.133325
Wijesundara, S., Hemachandra, T., Bandara, S. and Wijesundara, K., Investigation of the shear capacity of ultra high-performance fiber reinforced concrete beams using machine learning techniques, Struc. Infrastruc. Eng., 1-18(2025).
https://doi.org/10.1080/15732479.2025.2521480
Yonggui, W., Shuaipeng, L., Hughes, P. and Yuhui, F., Mechanical properties and microstructure of basalt fibre and nano-silica reinforced recycled concrete after exposure to elevated temperatures, Constr. Build. Mater., 247, 118561(2020).
https://doi.org/10.1016/j.conbuildmat.2020.118561
Zakare, H., Alisibramulisi, A., Sidek, M. N. M., Newman, A., Saari, N., Adnan, S. H. and Bhkari, N. M., The Effect of Palm Oil Fuel Ash (POFA) and Steel Fiber Addition to the Mechanical Properties of Ultra High-Performance Concrete (UHPC), Int. Conf. Sustain. Civ. Eng. Struc. Constr. Mater., 405-416(2020).
https://doi.org/10.1007/978-981-16-7924-7_26
Zeyad, A. M., Agwa, I. S., Abd-Elrahman, M. H. and Mostafa, S. A., Engineering characteristics of ultra-high performance concrete containing basil plant ash, Case Stud. Constr. Mater., 21, e03422(2024).
https://doi.org/10.1016/j.cscm.2024.e03422
Zeyad, A. M., Agwa, I. S., Abd-Elrahman, M. H. and Mostafa, S. A., Engineering characteristics of ultra-high performance concrete containing basil plant ash, Case Stud. Constr. Mater., 21, e03422 (2024).
https://doi.org/10.1016/j.cscm.2024.e03422
Zheng, Y., Zhuo, J., Zhang, Y. and Zhang, P., Mechanical properties and microstructure of nano-SiO2 and basalt-fiber-reinforced recycled aggregate concrete, Nanotechnol. Rev., 11(1), 2169-2189(2022).
