Influence of Cordia dichotoma Fibers and Zinc Oxide Nanoparticles on the Mechanical and Thermal Behavior of Epoxy Hybrid Composites
J. Environ. Nanotechnol., Volume 14, No 3 (September 2025) pp. 215-222
Abstract
Recently, natural fibers have been increasingly used in lightweight applications to reduce the reliance on synthetic materials. The reinforcing phase in this study consists of Cordia dichotoma fiber (CDF), while the matrix material is an epoxy polymer composite with zinc oxide (ZnO) nanofiller. To determine the mechanical properties of the hybrid composites, five composite laminates were made with different weight ratios of filler-to-fiber. The results indicate that the composite laminate sample (S1) showed better mechanical properties with a higher weight ratio of CDFs. These attributes include tensile strength (22.45 MPa), flexural strength (26.14 MPa), and impact energy absorption (25 J). Moreover, the addition of ZnO nanofiller contributed to improved thermal stability, with higher filler content elevating the degradation temperature to 454 °C. Scanning Electron Microscopy (SEM) was employed to analyze the surface interactions among the CDFs, ZnO nanofiller, and epoxy matrix, as well as to determine the failure modes of the composite laminates during mechanical testing.
Full Text
Reference
Ali, M. F., Hossain, M. S., Lithi, I. J., Ahmed, S. and Chowdhury, A. M. S., Fabrication and characterization of sustainable composites from animal fibers reinforced unsaturated polyester resin, Heliyon., 10(13), e33441(2024).
https://doi.org/10.1016/j.heliyon.2024.e33441
Al-Lhaibi, S. A. and Al-Shabander, B. M., Study the effect of ZnO nanoparticles reinforced sawdust /epoxy composites on mechanical properties, Dig. J. Nanomater. Biostruct., 17(3), 851–860(2022).
https://doi.org/10.15251/DJNB.2022.173.851
Andoko, A., Diharjo, K., Soedarsono, J. W., Gapsari, F., Rangappa, S. M. and Siengchin, S., Influence of various chemical treatments on mechanical, thermal and morphological characteristics of Cordia dichotoma fiber, Case Stud. Chem. Environ. Eng., 10(13), e33441(2024).
https://doi.org/10.1016/j.cscee.2024.100972
Ben, S. J., Jaisingh, S. J., Sivakumar, K., Mayakannan, A. V. and Arunprakash, V. R., Visco-Elastic, Thermal, Antimicrobial and Dielectric Behaviour of Areca Fibre-Reinforced Nano-silica and Neem Oil-Toughened Epoxy Resin Bio Composite, Silicon., 13(6), 1703–1712(2021).
https://doi.org/10.1007/s12633-020-00569-0
Diharjo, K., Andoko, A., Soedarsono, J. W., Gapsari, F., Rangappa, S. M. and Siengchin, S., Enhanced composite performance: Evaluating silane treatment on Cordia dichotoma Fibers, Result. Eng., 25, (2025).
https://doi.org/10.1016/j.rineng.2025.104260
Gapsari, F., Kartikowati, C. W., Madurani, K. A., Harmayanti, A. and Sulaiman, A. M., Enhanced PVA-bioplastic membranes with nanocellulose and hydroxyapatite derived from blood clam shells, Environ. Nanotechnol., Monit. Manage., 23, 101035(2025).
https://doi.org/10.1016/j.enmm.2024.101035
Gupta, R. K., Mayakannan, S., Vijayaraghavalu, S., Poornima, M. M., Nanthakumar, S. and Bhaskaran, N. A., Multi-objective Optimization of Bamboo-madar Fiber Reinforced Composites for Lightweight Automotive Applications using Machine Learning and Genetic Algorithms, J. Environ. Nanotechnol., 13(4), 358–376(2024).
https://doi.org/10.13074/jent.2024.12.244978
Harak, S. S., Krishnaveni, K., Karthick, K., Chinnarasu, K., Venkata Hari Prasad, P., Tonk, A. and Mayakannan, S., Experimental Study on the Mechanical Properties of Hybrid Areca and Abaca Fiber Reinforced Polymer Composites, J. Environ. Nanotechnol., 13(4), 92–101(2024).
https://doi.org/10.13074/jent.2024.12.244977
Hassan, G., Bhatti, I. and Shaikh, M. S., Investigating the Influence of Alkali over Morphology, Functional Groups, and Physical and Mechanical Properties of Fiber obtained from Cordia dichotoma (Gum Berry), Phys. Chem. Res., 12(2), 349–359(2024).
https://doi.org/10.22036/pcr.2023.408365.2381
Jayaramudu, J., Maity, A., Sadiku, E. R., Guduri, B. R., Varada Rajulu, A., Ramana, Ch. V. V. and Li, R., Structure and properties of new natural cellulose fabrics from Cordia dichotoma, Carbohydr. Polym., 86(4), 1623–1629(2011).
https://doi.org/10.1016/j.carbpol.2011.06.071
Jayaramudu, J., Reddy, G. S. M., Varaprasad, K., Sadiku, E. R., Ray, S. S. and Rajulu, A. V., Effect of alkali treatment on the morphology and tensile properties of Cordia dichotoma fabric/polycarbonate composites, Adv. Polym. Technol., 32(3), adv.21349(2013).
https://doi.org/10.1002/adv.21349
Kovačević, Z., Pilipović, A., Meheš, M. and Bischof, S., Zero Waste Concept in Production of PLA Biocomposites Reinforced with Fibers Derived from Wild Plant (Spartium junceum L.) and Energy Crop (Sida hermaphrodita (L.) Rusby), Polym., 17(2), 235(2025).
https://doi.org/10.3390/polym17020235
Kumar, R. S., Devi, V. V., Nivedhitha, D. M., Satya, S. S., Visakan, S., Sharma, S. B. and Kumar, S. S. B., Effect of nanoparticles in natural fiber reinforced polymer composites, Mater. Today Proc., xxxx, S2214785323020266(2023).
https://doi.org/10.1016/j.matpr.2023.04.130
Loganathan, K., Giri, R., Srinivasan, S. P. and Vimalanathan, P., Experimental investigation on mechanical, thermal, DMA, and dielectric analysis of Cordia dichotoma with PLA composites, Biomass Convers. Biorefin., 14(24), 31789–31804(2024).
https://doi.org/10.1007/s13399-023-04882-7
Mayakannan, S., Raj, J. B., Raja, V. L., & Nagaraj, M., Effectiveness of silicon nanoparticles on the mechanical, wear, and physical characteristics of PALF/sisal fiber–based polymer hybrid nanocomposites, Biomass Convers. Biorefin., 13(14), 13291–13305(2023).
https://doi.org/10.1007/s13399-023-04654-3
Meravi, M. K. and Panchore, V., Tribological and mechanical characteristics of glass/flax fiber-ZnO reinforced epoxy hybrid composite, Colloid Polym. Sci., 303(3), 411–426(2025).
https://doi.org/10.1007/s00396-024-05356-6
Reddy, B. M., Reddy, Y. V. M., Reddy, B. C. M. and Reddy, R. M., Mechanical, morphological, and thermogravimetric analysis of alkali-treated Cordia-Dichotoma natural fiber composites, J. Nat. Fibers, 17(5), 759–768(2020).
https://doi.org/10.1080/15440478.2018.1534183
Sakti, A. M., Darmadi, D. B., Gapsari, F., Widodo, T. D. and Ganda, A. N. F., Enhancing the structural and antibacterial properties of soybean hull fibers via alkali treatment and zinc oxide nanocoating, Cleaner Waste Syst., 11, (2025).
https://doi.org/10.1016/j.clwas.2025.100289
Sampathkumar, D., Mohankumar, A., Kulandaivel, A. and Packkirisamy, V., Experimental Investigation on the Micro Structural and Flame Retardant Properties of Various Natural Fiber Reinforced Composites, J. Nat. Fibers, 21(1), 2341125(2024).
https://doi.org/10.1080/15440478.2024.2341125
Senniangiri, N., Gokulkannan, S., Kumar, S. D. and Gokul, S., Enhancing Mechanical, Moisture Resistance, and Fire-retardant Properties of Nelumbo nucifera Fiber/Epoxy Nanocomposites with Zinc Oxide Nanoparticles, J. Environ. Nanotechnol., 14(1), 253–265(2025).
https://doi.org/10.13074/jent.2025.03.2511215
Sun, M., Yu, T., Zhang, H., Yang, Y., Wang, D., Cui, Y., Wang, J. and Pan, L., Enhancing the interfacial strength of jute fiber/polylactic acid composites via surface carboxymethylation pretreatment and in situ growth of ZnO nanorods, Compos. Interfaces., 31(5), 583–599(2024).
https://doi.org/10.1080/09276440.2023.2272100
Tasnim, T., Rabbi, M. S., Adil, M. M. and Hasib, M. A., An experimental study on jute/banana fiber reinforced poly (vinyl alcohol) composites with nanofiller, J. Vinyl Add. Technol., 30(5), 1327–1340(2024).
https://doi.org/10.1002/vnl.22127
Thandavamoorthy, R., Mohanavel, V., Sivapragasam, A., Vekariya, V., Paul, D., Velmurugan, P., Al Obaid, S., Alharbi, S. A. and Basavegowda, N., Environmental sustainability and waste conversion of Prosopis juliflora fibre-reinforced ZnO nanofiller particulates PLA composite- mechanical and thermal analysis, Heliyon., 10(19), e38327(2024).
https://doi.org/10.1016/j.heliyon.2024.e38327
Tumusiime, G., Wambua, P., Rwahwire, S., Njuguna, D. and Yiga, V. A., Production and mechanical characterization of reinforced zinc oxide nanoparticle-coated silk waste bio-composites, Polym. Bull., 80(8), 8799–8818(2023).
https://doi.org/10.1007/s00289-022-04475-w
Yang, Y., Nie, W., Zhang, H., Yu, T., Wu, K., Wang, J., Cui, Y. and Pan, L., Homogeneous and aligned ZnO nanorods@Jute fibers for enhanced mechanical/microwave absorbing performance and thermal stability, Mater. Chem. Phys., 295, 127031(2023).
