Nano-reinforcement and Synthesis of Al 8090-based Hybrid Composites with B4C and Coconut Shell Charcoal for Enhanced Tribological Performance
J. Environ. Nanotechnol., Volume 14, No 3 (September 2025) pp. 559-572
Abstract
This study investigates the tribological properties of Aluminum 8090-based hybrid composites reinforced with 3 wt. % Boron Carbide (B4C) and varying weight percentages (2%, 3%, and 4%) of coconut shell charcoal (CSC) nanoparticles. The composites were fabricated using stir casting and characterized for their density, porosity, hardness, and wear behavior under different operating conditions. The density decreased with increasing CSC content, whereas the porosity remained below 2.37%, indicating effective particle dispersion. The hardness improved with higher CSC loading, reaching 133.1 HV for the 4% CSC composite. Tribological tests were conducted using a pin-on-disk tribometer, varying the applied load (10, 20, and 30 N), temperature (27, 50, and 100 °C), and sliding distance (500, 1000, and 1500 m). The Taguchi method and ANOVA revealed that the sliding distance was the most influential factor for both the wear rate and coefficient of friction (COF), followed by the CSC content. The optimal conditions for minimal wear (0.01422 mm³/m) and COF (0.449) were found to be 10 N, 27 °C, 2% CSC, and 500 m. The 4% CSC composite exhibited the best overall performance, with low porosity (1.99%), high hardness (133.1 HV), and a reduced COF (0.406). SEM-EDS analysis confirmed the uniform dispersion of the B4C and CSC reinforcements within the Al 8090 matrix, with minimal porosity and strong interfacial bonding. The results highlight the potential of Al 8090/B4C/CSC hybrid composites for applications requiring high wear resistance and low friction, such as in aerospace and automotive components.
Full Text
Reference
Adediran, A. A., Alaneme, K. K., Oladele, I. O., and Akinlabi, E. T., Wear characteristics of aluminium matrix composites reinforced with Si-based refractory compounds derived from rice husks, Cogent Eng., 7(1), 1826634 (2020).
https://doi.org/10.1080/23311916.2020.1826634
Akgümüş, G. A. D., Bayraktar, C. and Hoşkun, M., A review on processing, mechanical and wear properties of Al matrix composites reinforced with Al2O3, SiC, B4C and MgO by powder metallurgy method, J. Mater. Res. Technol., 31, 1132–1150 (2024).
https://doi.org/10.1016/J.JMRT.2024.06.110
Arunkumar, S., Ashokkumar, R., Sundaram, S. M., Suketh Kanna, K. M., and Vigneshwara, S., Optimization of wear behaviour of Al7075 hybrid metal matrix composites using Taguchi approach, Mater. Today: Proc., 33, 570–577 (2020).
https://doi.org/10.1016/j.matpr.2020.05.453
Arunkumar, S. and Kumar, A. S., Studies on Egg Shell and SiC Reinforced Hybrid Metal Matrix Composite for Tribological Applications, Silicon, 14(5), 1959–1967 (2022).
https://doi.org/10.1007/s12633-021-00965-0
Asha, P. B., Murthy, S. S. and Suresha, C. N., Investigation of physical, mechanical & wear behavior of aluminium composite carrying ceramic Boron carbide particles, Mater. Today: Proc., 47, 2221–2226 (2021).
https://doi.org/10.1016/j.matpr.2021.04.182
Bhowmik, A., Bhattacharjee, B., Akinwande, A. A., Majumder, P., Giri, J., Kumar, P. S. and Katiyar, J. K., Optimization of tribological performance of TiB2-reinforced Al6063 composite using grey-fuzzy tool, Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 238(9), 1066-1078 (2024).
https://doi.org/10.1177/13506501241246845
Dwivedi, S. P., Maurya, M., Saxena, A. and Sharma, S., Synthesis and characterization of spent alumina catalyst and grinding sludge reinforced aluminium-based composite material, Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 236(10), 5523–5534 (2022).
https://doi.org/10.1177/09544062211061451
Halil, K., Ismail, O. I., Sibel, D. and Ramazan, Çi., Wear and mechanical properties of Al6061/SiC/B4C hybrid composites produced with powder metallurgy, J. Mater. Res. Technol., 8(6), 5348–5361 (2019).
https://doi.org/10.1016/J.JMRT.2019.09.002
Harish, T. M., Mathai, S., George, M., Harisankar, M., illimattathil, A. G., Francis, B. and Venugopal V. A., Development of aluminium 5083/B4C/carbonized coconut shell ash hybrid composite using friction stir processing, Mater. Today: Proc., 72, 3149–3153 (2023).
https://doi.org/10.1016/j.matpr.2022.10.167
Hynes, N. R. J., Raja, S., Tharmaraj, R., Pruncu, C. I. and Dispinar, D., Mechanical and tribological characteristics of boron carbide reinforcement of AA6061 matrix composite, J. Braz. Soc. Mech. Sci. Eng., 42(4), 155 (2020).
https://doi.org/10.1007/s40430-020-2237-2
Kar, C. and Surekha, B., Effect of red mud and TiC on friction and wear characteristics of Al 7075 metal matrix composites, Aust. J. Mech. Eng., 20(1), 14–23 (2019).
https://doi.org/10.1080/14484846.2019.1651138
Karpasand, F., Ardestani, M. and Abbasi, A., The effect of powder addition manner and volume fraction of reinforcement on tribological behavior of Al7075/B4C surface composite produced by friction stir processing, J. Compos. Mater., 54(21), 2873–2886 (2020).
https://doi.org/10.1177/0021998320904143
Karthe, M., Karuppusamy, S., Sureshkumar, B. and Ali, A. N., Mechanical and wear properties of Al7075- B4C–Gr metal matrix composites fabricated by the using stir casting method, Mater. Today: Proc., 77. 389–393 (2023).
https://doi.org/10.1016/J.MATPR.2022.10.162
Karthikeyan, I., Dhinakaran, V. and Rajkumar, V., Evaluation of mechanical properties of aluminium 6063-Borosilicate reinforced metal matrix composite, AIP Conf. Proc., 2283(1), 020031 (2020).
https://doi.org/10.1063/5.0025114
Kumar, A., Singh, R. C. and Chaudhary, R., Investigation of Nano-Al2O3 and Micro-coconut Shell Ash (CSA) Reinforced AA7075 Hybrid Metal–Matrix Composite Using Two-Stage Stir Casting, Arab. J. Sci. Eng., 47(12), 15559–15573 (2022).
https://doi.org/10.1007/S13369-022-06728-2
Lan, X., Li, K., Wang, J., Yang, M., Lu, Q. and Du, Y., Developing Al–Fe–Si alloys with high thermal stability through tuning Fe, Si contents and cooling rates, Intermetallics, 144, 107505 (2022).
https://doi.org/10.1016/J.INTERMET.2022.107505
Lokeshwari, M., Sagar, P. V., Kumar, K. D., Thirupathy, D., Subbiah, R., Ganeshan, P., Seikh, A. H., Mohammed, S. M. A. K. and Christopher, D., Optimization and Tribological Properties of Hybridized Palm Kernel Shell Ash and Nano Boron Nitride Reinforced Aluminium Matrix Composites, J. Nanomater., 2022(1), 8479012 (2022).
https://doi.org/10.1155/2022/8479012
Mahanta, S., Chandrasekaran, M., Samanta, S. and Arunachalam, R., Multi-response ANN modelling and analysis on sliding wear behavior of Al7075/B4C/fly ash hybrid nanocomposites, Mater. Res. Express, 6(8), 0850h4 (2019).
https://doi.org/10.1088/2053-1591/ab28d8
Manikandan, R., Arjunan, T. V., and Akhil, A. R. Studies on microstructural characteristics, mechanical and tribological behaviors of boron carbide and cow dung ash reinforced aluminum (Al 7075) hybrid metal matrix composite, Compos. Part B: Eng., 183, 107668 (2020).
https://doi.org/10.1016/j.compositesb.2019.107668
Oza, M. J., Schell, K. G., Bucharsky, E. C., Laha, T. and Roy, S., Developing a hybrid Al–SiC-graphite functionally graded composite material for optimum composition and mechanical properties, Mater. Sci. Eng.: A, 805, 140625 (2021).
https://doi.org/10.1016/J.MSEA.2020.140625
Pattar, J., Ramesh, D., Malghan, R. L., Kumar, A., Kumar, P. and H. M. V., Investigation of AA6063-based metal–matrix composites reinforced with TiO2 dispersoids through digitally assisted techniques for mechanical, tribological, and microstructural characterizations, Front. Mech. Eng., 10, 1393959 (2024).
https://doi.org/10.3389/fmech.2024.1393959
Pawar, S. Y., Haider, J., Pintaude, G., Sekar, S. M., Kolhe, V., Chandratre, K., Sonawane, S. and Ritapure, P., Mechanical and Tribological Behavior of LM26/SiC/Ni-Gr Hybrid Composites, J. Compos. Sci., 7(4), 159 (2023).
https://doi.org/10.3390/JCS7040159
Pawar, S. Y. and Kharde, Y. R., Tribological characterization of LM26/SiC/Ni.-Gr. Hybrid aluminium matrix composites (HAMCs) for high temperature applications, Mater. Today Proc., 37(2), 793–800 (2021).
https://doi.org/10.1016/j.matpr.2020.06.003
Poornesh, M., Bhat, S., Bellairu, P. K. and McDermott, O., Enhancement of Tensile Strength of Coconut Shell Ash Reinforced Al-Si Alloys: A Novel Approach to Optimise Composition and Process Parameters Simultaneously, Process., 12(7), 1521 (2024).
https://doi.org/10.3390/PR12071521
Prakash, R. V. and Das, C. V., Edm Investigation of Al 7075 /B4 C/Zro2 Hybrid Metal Matrix Composite by Applying Response Surface Method, Int. J. Adv. Res. Eng. Technol., 12(3), 152-164(2021).
https://doi.org/10.34218/IJARET.12.3.2021.0017
Raju, S. S., Rao, G. S. and Siva, B. V., Experimental studies of mechanical properties and tribological behaviour of aluminium composite reinforced with coconut shell ash particulates, Int. J. Mater. Eng. Inn., 9(2), 140 (2018).
https://doi.org/10.1504/IJMATEI.2018.10014995
Ravi, K. K., Pridhar, T. and Balaji, S. V. S., Mechanical properties and characterization of zirconium oxide (ZrO2) and coconut shell ash(CSA) reinforced aluminium (Al 6082) matrix hybrid composite, J. Alloys Compd., 765, 171–179 (2018).
https://doi.org/10.1016/J.JALLCOM.2018.06.177
Satheesh, M. and Pugazhvadivu, M., Investigation on physical and mechanical properties of Al6061-Silicon Carbide (SiC)/Coconut shell ash (CSA) hybrid composites, Physica B Condens. Matter, 572, 70–75 (2019).
https://doi.org/10.1016/J.PHYSB.2019.07.058
Sharma, O. P. and Meena, A., Study of mechanical properties and wear behavior of aluminum 6061 matrix composites reinforced with Hematite and Titania, Mater. Today Proc., 44, 5028–5036 (2021).
https://doi.org/10.1016/J.MATPR.2021.01.131
Sharma, S. K., Gajević, S., Sharma, L. K., Pradhan, R., Sharma, Y., Miletić, I. and Stojanović, B., Progress in Aluminum-Based Composites Prepared by Stir Casting: Mechanical and Tribological Properties for Automotive, Aerospace, and Military Applications, Lubr., 12(12), 421 (2024).
https://doi.org/10.3390/LUBRICANTS12120421
Siengchin, S., A review on lightweight materials for defence applications: Present and future developments, Def. Technol., 24, 1–17 (2023).
https://doi.org/10.1016/J.DT.2023.02.025
Silambarasan, B., and Karthikeyan, G., Experimental investigation of coconut shell charcoal and boron carbide/zirconium dioxide in aluminium 7075 matrix composites under varying operating conditions: a comparative analysis, Mater. Res. Express, 10(9), 096512 (2023).
https://doi.org/10.1088/2053-1591/acf8b1
Singh, J., Chauhan, A., & Sharma, A., Effect of boron carbide (B₄C) and silicon carbide (SiC) reinforcement on mechanical properties of aluminum-based composites. J. Alloys Compd., 651, 327–335 (2016).
https://doi.org/10.1016/j.jallcom.2015.08.138
Subramaniam, B., Natarajan, B., Kaliyaperumal, B. and Chelladurai, S. J. S., Wear behaviour of aluminium 7075—boron carbide- coconut shell fly ash reinforced hybrid metal matrix composites, Mater. Res. Express, 6(10), 1065d3 (2019).
https://doi.org/10.1088/2053-1591/AB4052
Subramaniam, B., Natarajan, B., Kaliyaperumal, B., and Chelladurai, S.J.S., Investigation on mechanical properties of aluminium 7075 - boron carbide - coconut shell fly ash reinforced hybrid metal matrix composites, China Foundry, 15(6), 449–456 (2018).
https://doi.org/10.1007/S41230-018-8105-3
Sudhakar, U., Raghavulu, K. V., Jani, S. P., Shetty, S. K. and Haile, A., Mechanical and microstructural analysis of AA7075/B4C/ZrO2 hybrid composite, J. Mater. Sci.: Mater. Eng., 20(1), 55 (2025).
https://doi.org/10.1186/S40712-025-00232-9
Yekinni, A. A., Bello, S. K., Bajela, G. G. and Adigun, I. A., Effect of Coconut Shell Ash and Graphite Particles on Microstructure and Mechanical Properties of Recycled Aluminium Composites, Int. J. Adv. Sci. Res. Eng., 6(10), 61–71 (2020).
