Investigation of the Mechanical and Morphological Behavior of Hybrid PALF-Kenaf Composites Reinforced with Hydroxyapatite and Zinc Oxide Nanoparticles
J. Environ. Nanotechnol., Volume 14, No 3 (September 2025) pp. 443-453
Abstract
This research examines the mechanical, biodegradable, and morphological properties of pineapple leaf fiber (PALF), kenaf fiber (KF), and hybridized PALF-KF composites reinforced with hydroxyapatite and zinc oxide nano-fillers. The composites were fabricated using the hand lay-up technique followed by compression molding. Mechanical properties such as tensile, impact, flexural, and hardness were evaluated in accordance with ASTM standards. The PALF–kenaf hybrid composite achieved a maximum tensile strength of 55.38 MPa, impact strength of 7.68 kJ/m2, and hardness of 84.62, while the neat PALF composite exhibited the highest flexural strength of 106.56 MPa. Biodegradability assessments indicated that natural fiber composites degraded more significantly than nano-reinforced composites, with PALF-rich variants showing greater weight loss over time. SEM analysis revealed strong fiber–matrix bonding in the hybrid composites. However, the agglomeration of nano-fillers resulted in lower strength values for PALF-KF hybrid composites. These findings offer valuable insights into optimizing hybrid natural fiber composites to enhance their mechanical and morphological behavior.
Full Text
Reference
Ambekar, A. M., Muralishwara, K., Hindi, J., Acharya, S., Naik, N., Gurumurthy, B. M., Hiremath, P. and Kasipandian, K., Effect of Seawater Absorption on Mechanical and Flexural Properties of Pineapple Leaf Fiber Reinforced Epoxy Nanoclay Composites, ES Mater. Manuf., 22, 1067 (2023).
https://doi.org/10.30919/esmm1067
Arunachalam, S. J., Thanikodi, S. and Saravanan, R., Effect of nano-hybridization on flexural and impact behavior of jute/kenaf/glass fiber-epoxy composites for automotive application, Results Eng., 25, 104571 (2025).
https://doi.org/10.1016/j.rineng.2025.104571
Cabrera, G. P., Marrero, M. D. and Benítez, A. N., Disintegration and marine biodegradability of biocomposite using Pennisetum setaceum fiber and PLA as matrix, Polym. Degrad. Stab., 230, 111026 (2024).
https://doi.org/10.1016/j.polymdegradstab.2024.111026
Devi, A. S. H., Shenoy, G. H., Auradi, V. and Shetty, S. K., Synthesis and Mechanical Characterization of Pineapple Leaf Fibers and Boron Carbide Fillers Reinforced Lapox L-12 Epoxy Composites, J. Mines Met. Fuels, 73(5), 1193–1202 (2025).
https://doi.org/10.18311/jmmf/2025/48107
Ejaz, M., Azad, M. M., Shah, A. U. R., Afaq, S. K. and Song, J.-I., Mechanical and Biodegradable Properties of Jute/Flax Reinforced PLA Composites, Fibers Polym., 21(11), 2635–2641 (2020).
https://doi.org/10.1007/s12221-020-1370-y
Fitri, M. F. M., Asyraf, M. R. M., Hassan, S. A. and Ilyas, R. A., Unveiling the physico-mechanical properties of kenaf yarn fiber-reinforced acrylonitrile butadiene styrene composites: Effect of quasi-isotropic lay-up sequences, Polym. Compos., 45(10), 9362–9375 (2024).
https://doi.org/10.1002/pc.28414
Gaddala, B., Kandavalli, S. R., Raghavendran, G., Sivaprakash, A., Rallabandi, R., Sundramurthy, V. P., Selvaraju, M. and Sugumar, M., Exploring the impact of hybridization on green composites: Pineapple leaf and sisal fiber reinforcement using poly(furfuryl alcohol) bioresin, Z. Fur Phys. Chem., 239(4), 495–518 (2025).
https://doi.org/10.1515/zpch-2024-0772
Hombal, R. R., Shivarudraiah, Shivanand, H. K., Fabrication and Characterization of Kenaf and Kevlar Fibre Reinforced Graphene Filled Hybrid Composite Laminates for Engineering Applications, J. Mines Met. Fuels, 73(5), 1379–1387 (2025).
https://doi.org/10.18311/jmmf/2025/47621
Jeon, H. -C. and Kim, Y. -S., Mechanical Performance of Cellulose Nanocrystal and Bioceramic-Based Composites for Surgical Training, Polym., 16(19) 2849 (2024).
https://doi.org/10.3390/polym16192849
Jeyaraman, J., Jesuretnam, B. R. and Ramar, K., Effect of stacking sequence on dynamic mechanical properties of Indian almond–Kenaf fiber reinforced hybrid composites, J. Nat. Fibers, 19(12), 4381–4392 (2022).
https://doi.org/10.1080/15440478.2020.1858219
Kumar, N., Singh, S., Singh, A. and Han, T., Mechanical, Water Absorption, and Tribological Behavior of Polymer Composites: Role of Pineapple Leaf Fiber Orientation, Lubr., 13(4), 161 (2025).
https://doi.org/10.3390/lubricants13040161
Lhaibi, A. S. A. and Shabander, A. B. M., Study the effect of ZnO nanoparticles reinforced sawdust /epoxy composites on mechanical properties, Dig. J. Nanomater. Biostruct., 17(3), 851–860 (2022).
https://doi.org/10.15251/DJNB.2022.173.851
Mayakannan, S., Raj, J. B., Raja, V. L. and Nagaraj, M., Effectiveness of silicon nanoparticles on the mechanical, wear, and physical characteristics of PALF/sisal fiber–based polymer hybrid nanocomposites, Biomass Convers. Biorefin., 13(14), 13291–13305 (2023).
https://doi.org/10.1007/s13399-023-04654-3
Mohapatra, D. K., Deo, C. R., Mishra, P. and Dash, P., Influence of pistachio shell filler addition and interply hybridization on mechanical and thermal performances of polyester composites, J. Elastomers Plast., 56(2), 169–193 (2024).
https://doi.org/10.1177/00952443231224068
Muralishwara, K., Fernandes, L., Kalkura, R. and Bangera, S., Effect of Surface Modified Montmorillonite Nanoclay on Tensile and Flexural Properties of Pineapple Leaf Fiber Reinforced Epoxy Composite, Mater. Res., 26, e20220437 (2023).
https://doi.org/10.1590/1980-5373-MR-2022-0437
Murugan, R., Ramesh, R., Karthikeyan, K. R. and Santhoshkumar, B., Experimental Investigation On Effect Of Cyclic Loading On Free Vibration Characteristics Of Glass/Jute Hybrid Composite Beams, J. Appl. Sci. Eng., 26(3), 347–355 (2023).
https://doi.org/10.6180/jase.202303_26(3).0006
Nagaraja, S., Anand, P. B., Shivakumar, H. D. and Ammarullah, M. I., Influence of fly ash filler on the mechanical properties and water absorption behaviour of epoxy polymer composites reinforced with pineapple leaf fibre for biomedical applications, RSC Adv., 14(21), 14680–14696 (2024).
https://doi.org/10.1039/d4ra00529e
Nayak, S., Mohanty, J. R., Samal, P. R. and Nanda, B. K., Polyvinyl Chloride Reinforced with Areca Sheath Fiber Composites—An Experimental Study, J. Nat Fibers, 17(6), 781–792 (2020).
https://doi.org/10.1080/15440478.2018.1534186
Raghunathan, V., Palani, K., Shinu, P., Dhilip, J. D. J., Yoganjaneyulu, G. and Ganesh, S., Influence of Parthenium Hysterophorus and Impomea Pes-caprae Fibers Stacking Sequence on the Performance Characteristics of Epoxy Composites, J. Nat. Fibers, 19(12), 4456–4466 (2022).
https://doi.org/10.1080/15440478.2020.1863292
Reddy, M., Adaveesh, B., Mohankumar, T. S. and Nagaral, M., Tensile and Flexural Behaviour Of Graphite Filler Particles and Pineapple Leaf Fiber (Palf) Reinforced Polymer Composite, Metall. Mater. Eng., 28(1), 141–155 (2022).
Sabir, M., Ali, A., Siddiqui, U., Muhammad, N., Khan, A. S., Sharif, F., Iqbal, F., Shah, A. T., Rahim, A. and Rehman, I. U., Synthesis and characterization of cellulose/hydroxyapatite based dental restorative composites, J. Biomater. Sci. Polym. Ed., 31(14), 1806–1819 (2020).
https://doi.org/10.1080/09205063.2020.1777827
Saha, A., Kumar, S. and Kumar, A., Influence of pineapple leaf particulate on mechanical, thermal and biodegradation characteristics of pineapple leaf fiber reinforced polymer composite, J. Polym. Res., 28(2), 66 (2021).
https://doi.org/10.1007/s10965-021-02435-y
Sathish, K. R., Devi, V. V., Nivedhitha, D. M., Satya, S. S., Visakan, S., Sharma, B. S. and Kumar, S. S. B., Effect of nanoparticles in natural fiber reinforced polymer composites, Mater. Today: Proc., (2023).
https://doi.org/10.1016/j.matpr.2023.04.130
Sathyaseelan, P., Kumar R, R., Rajesh, D., Raja, K., Manivannan, J. and Raju, M., Mechanical characteristics of kenaf-glass fiber reinforced hybrid composites by varying the stacking sequences, Phys. Scr., 99(10), 1059b3 (2024).
https://doi.org/10.1088/1402-4896/ad79c7
Sathyaseelan, P., Sellamuthu, P. and Palanimuthu, L., Influence of stacking sequence on mechanical properties of areca-kenaf fiber-reinforced polymer hybrid composite, J. Nat. Fibers, 19(1), 369–381 (2022).
https://doi.org/10.1080/15440478.2020.1745118
Shivayogi, B. H., Manjunatha, T. S., Gouda, S. P. S., Maruthi, P. B. H., and Prashanth, P. M., Influence of layering sequence on performance of jute/wool epoxy hybrid composites: a comparative study with automotive plastic, Eng. Res. Express, 6(1), 015522 (2024).
https://doi.org/10.1088/2631-8695/ad2ef8
Singh, S. P., Sharma, A., Singh, V. and Mishra, S., Effects of fiber type, content, orientation, and surface treatments on the mechanical properties of PAFRP composite, Eng. Res. Express, 6(1), 015011 (2024).
https://doi.org/10.1088/2631-8695/ad1432
Torres, M., Rodriguez, V. R., Alcantara, P. I., and Urquiza, F. E., Mechanical properties and fracture behaviour of agave fibers bio-based epoxy laminates reinforced with zinc oxide, J. Ind. Text., 51(4), 5847S-5868S (2022).
https://doi.org/10.1177/1528083720965689
Vijayan, R., Natarajan, E., Palanikumar, K., Krishnamoorthy, A., Markandan, K. and Ramesh, S., Effect of hybridization and stacking sequences on mechanical properties and thermal stability of aloe vera-roselle-glass fiber reinforced polymer composites, Polym. Compos., 44(10), 6593–6603 (2023).
https://doi.org/10.1002/pc.27582
Yashas, G. T. G., Madhu, P., Kushvaha, V., Rangappa, S. M. and Siengchin, S., Comparative evaluation of areca/carbon/basalt fiber reinforced epoxy/bio epoxy based hybrid composites, Polym. Compos., 43(7), 4179–4190 (2022a).
https://doi.org/10.1002/pc.26680
Yashas, G. T. G., Vinod, A., Madhu, P., Rangappa, M. S., Siengchin, S., and Jawaid, M., Mechanical and thermal properties of flax/carbon/kevlar based epoxy hybrid composites, Polym. Compos., 43(8), 5649–5662 (2022b).
https://doi.org/10.1002/pc.26880
Zalinawati, M., Siregar, J. P., Tezara, C., Jaafar, J., Hamdan, M. H. M., Oumer, A. N., and Rihayat, T., Effect of Surface Modification on Mechanical Properties of Buri Palm (Corypha Utan) Fibre Composite Reinforcement, Int. J. Automot. Mech. Eng., 17(4), 8298–8309 (2020).
