Experimental Investigation on Mechanical and Microstructural Properties of Hybrid Composite Materials for Ballistic Armor Applications
J. Environ. Nanotechnol., Volume 14, No 3 (September 2025) pp. 516-522
Abstract
Recently, industries have increasingly required lightweight materials with high strength for specific applications, such as in the manufacturing of ballistic armor. In this work, three synthetic fibers are used: Kevlar, carbon, and glass fiber, and two different sample laminates are fabricated. The fibers are arranged using a hand lay-up process. Out of the two samples, one includes Expanded Polyethylene (EPE) foam—to increase the thickness—while the other does not contain EPE foam. The samples are fabricated in a specific fiber sequence, starting with Kevlar, followed by carbon, and then glass fiber. In the sample with foam, two EPE foam sheets are used and placed between two sequential layers of fibers. Mechanical and microstructural characterization was performed, including tensile testing, flexural testing, DMA testing, and SEM analysis, and the corresponding results were obtained. These fiber laminates are intended for ballistic armor applications, where the three fibers contribute by reducing weight, increasing strength, and enhancing performance, thereby preventing bullet penetration and ultimately saving human life. Advanced materials like Kevlar, ceramic plates, and ultra-high molecular weight polyethylene are used in modern ballistic armour to offer lightweight, yet effective, protection against a range of threat levels, including rifle and handgun ammunition. With continuous research aimed at enhancing protection-to-weight ratios and multi-threat capabilities, these protective systems go beyond personal body armour to include vehicle armouring, aircraft protection, and stationary barriers for critical infrastructure.
Full Text
Reference
Abtew, M. A., Boussu, F., Bruniaux, P., Loghin, C. and Cristian, I., Ballistic impact mechanisms–a review on textiles and fiber-reinforced composites impact responses, Compos. Struct., 223, 110966(2019).
https://doi.org/10.1016/j.compstruct.2019.110966
Benzait, Z. and Trabzon, L., A review of recent research on materials used in polymer–matrix composites for body armor application, J. Compos. Mater., 52(23), 3241-3263(2018).
https://doi.org/10.1177/002199831876400
Braga, F. O., Bolzan, L.T., Luz, F. S., Lopes, R. H. L. M., Lima, E. P., J. and Monteiro, S. N., High energy ballistic and fracture comparison between multilayered armor systems using non-woven curaua fabric composites and aramid laminates, J. Mater. Res. Technol., 6(4), 417-422 (2017).
https://doi.org/10.1016/j.jmrt.2017.08.001
Bucura, F., Spiridon, S. -I., Ionete, R. E., Marin, F., Zaharioiu, A. M., Armeanu, A., Badea, S. -L., Botoran, O. R., Ionete, E. I., Niculescu, V. -C. and Marius, C., Selectivity of MOFs and Silica Nanoparticles in CO2 Capture from Flue Gases, Nanomater., 13(19), 2637(2023).
https://doi.org/10.3390/nano13192637
Grujicic, M., Pandurangan, B., Koudela, K. L. and Cheeseman, B. A., A computational analysis of the ballistic performance of light-weight hybrid composite armors, Appl. Surf. Sci., 253(2), 730-745(2006).
https://doi.org/10.1016/j.apsusc.2006.01.016
Fayaz, H., Karthik, K., Christiyan, K. G. J., Arun, K. M., Sivakumar, A., Kaliappan, S., Mohamed, M., Ram, S. and Simon, Y., An Investigation on the Activation Energy and Thermal Degradation of Biocomposites of Jute/Bagasse/Coir/Nano TiO2/Epoxy-Reinforced Polyaramid Fibers, J. Nanomater., 2022(1), 3758212 (2022).
https://doi.org/10.1155/2022/3758212
Ganesh, R., Karthik, K., Manimaran, A. and Saleem, M., vibration-damping characteristics of cantilever beam using piezoelectric actuator, Int. J. Mech. Eng. Technol., 8(6), 1-10(2017).
Jambari, S., Yahya, M. Y., Abdullah, M. R. and Jawaid, M., Woven Kenaf/Kevlar Hybrid Yarn as potential fiber reinforced for anti-ballistic composite material, Fib. Polym., 18(3), 563-568(2017).
https://doi.org/10.1007/s12221-017-6950-0
Jebarose, J. S., Udaya, P. J., Čep, R. and Karthik, K., Multi-Objective Optimization of Machining Parameters for Drilling LM5/ZrO2 Composites Using Grey Relational Analysis, Mater., 16(10), 3615(2023).
https://doi.org/10.3390/ma16103615
Karthik, K. and Senthilkumar, P., Tribological Characteristics of Carbon-Epoxy with Ceramic Particles Composites for Centrifugal Pump Bearing Application, Int. J. ChemTech Res., 8(6), 612-620(2015).
Karthik, K. and Manimaran, A., Wear behaviour of ceramic particle reinforced hybrid polymer matrix composites, Int. J. Amb. Energy, 41(14), 1608-1612(2020).
https://doi.org/10.1080/01430750.2018.1525583
Karthik, K., Rajamani, D., Venkatesan, E. P., Shajahan, M. I., Rajhi, A. A., Aabid, A., Baig, M. and Saleh, B., Experimental Investigation of the Mechanical Properties of Carbon/Basalt/SiC Nanoparticle/Polyester Hybrid Composite Materials, Cryst., 13(3), 415(2023).
https://doi.org/10.3390/cryst13030415
Karthik, K., Rathinasuriyan, C., Raja, T. and Sankar, R., Mechanical Characterization of Kenaf/Carbon Fiber Reinforced Polymer Matrix Composites with Different Stacking Sequence, Bio-Fib. Reinf. Compos. Mater., 175-187(2022).
https://doi.org/10.1007/978-981-16-8899-7
Krishnasamy, K., Jayavelu, U. P., Joseph, S. B., Brailson, M., Effect of stacking sequence and silicon carbide nanoparticles on properties of carbon/glass/Kevlar fiber reinforced hybrid polymer composites, polym. compos., 43(9), 6096–6105(2022).
https://doi.org/10.1002/pc.26912
Lin, Q., Zhang, F., Xu, X., Yang, H., Mao, Q., Xian, D., Yao, K. and Meng, Q., A Flexible Pressure Sensor Based on Graphene/Epoxy Resin Composite Film and Screen Printing Process, Nanomater., 2023; 13(19), 2630(2023).
https://doi.org/10.3390/nano13192630
Luz, F. S. D., Lima, J. E. P., Louro, L. H. L. and Monteiro, S. N., Ballistic test of multilayered armor with intermediate epoxy composite reinforced with jute fabric, Mater. Res., 18, 170-177(2015).
https://doi.org/10.3390/su141710591
Luz, F. S. D., Monteiro, S. N., Lima, E. S. and Lima, É. P., Ballistic application of coir fiber reinforced epoxy composite in multilayered armor, Mater. Res., 20(2), 23-28(2017).
http://dx.doi.org/10.1590/1980-5373-MR-2016-0951
Mawkhlieng, U., Majumdar, A. and Laha, A., A review of fibrous materials for soft body Armor applications, RSC adv., 10(2), 1066-1086(2020).
https://doi.org/10.1039/C9RA06447H
Medvedovski, E., Lightweight ceramic composite Armor system, Adv. Appl. Ceram., 105(5), 241-245(2006).
https://doi.org/10.1179/174367606X113537
Morye, S. S., Hine, P. J., Duckett, R. A., Carr, D. J. and Ward, I. M., Modelling of the energy absorption by polymer composites upon ballistic impact, Compos. sci. technol., 60(14), 2631-2642(2000).
https://doi.org/10.1016/S0266-3538(00)00139-1
Naik, S., Dandagwhal, R. D. and Loharkar, P. K., A review on various aspects of Kevlar composites used in ballistic applications, Mater. Today: Proce., 21, 1366-1374(2020).
https://doi.org/10.1016/j.matpr.2020.01.176
Ramesh, V., Karthik, K., Cep, R. and Elangovan, M., Influence of Stacking Sequence on Mechanical Properties of Basalt/Ramie Biodegradable Hybrid Polymer Composites, Polym., 15(4), 985(2023).
https://doi.org/10.3390/polym15040985
Regassa, Y., Likeleh, G. and Uppala, R., Modeling and simulation of bullet resistant composite body armor, Inter. J. Res. Stud. Sci., 14(3), 39-44(2014).
Sikarwar, R. S., Velmurugan, R., Madhu, V., Experimental and analytical study of high velocity impact on Kevlar/Epoxy composite plates, Cent. Eur. J. Eng., 2(4) 638– 649(2012).
https://doi.org/10.2478/s13531-012-0029-x
Siva, K. M., Rajamani, D., El-Sherbeeny, A. M., Balasubramanian, E., Karthik, K., Hussein, H. M. A. and Astarita, A., Intelligent Modeling and Multi-Response Optimization of AWJC on Fiber Intermetallic Laminates through a Hybrid ANFIS-Salp Swarm Algorithm, Mater., 15(20), 7216(2022).
