Evaluating the Mechanical Features of Nano Alumina Reinforced Magnesium Alloy-fly Ash Nanocomposites
J. Environ. Nanotechnol., Volume 14, No 2 (June 2025) pp. 96-104
Abstract
In this work, hybrid magnesium nanocomposite (HMNC) was fabricated with ultrasonic cavitation assisted bottom pouring stir casting method. For this, fixed quantity (7.5 wt.%) of fly ash (FA) and varying proportions of nano alumina (nAl2O3) (0, 0.5, 1, 1.5, and 2 wt.%) in AZ61 magnesium alloy matrix were used. Microstructural images reveal near homogeneous distribution of reinforcements with nAl2O3 available at the grain boundaries. The physical and mechanical properties were determined as per ASTM standards. It is found that the density and porosity tend to rise with increasing nAl2O3 content, whereas the porosity of 2 wt.% addition of nAl2O3 was very significant. The AZ61 alloy reinforced with 1.5 wt.% nAl2O3 and 7.5 wt.% FA exhibited enhanced strength and stiffness, which can be attributed to the Orowan strengthening mechanism and increased dislocation density. The 0.5 and 1 wt.% nAl2O3 reinforcement may be insufficient to effectively impede dislocation motion leading to limited improvements in mechanical properties. On the other hand, 2 wt.% nAl2O3 reinforcement leads to particle agglomeration and poor dispersion. This in turn, weakens the matrix-reinforcement interface and diminishes mechanical properties.
Full Text
Reference
Ahmadian, H., Zhou, T., Alansari, A., Kumar, A. S., Fathy, A., Elmahdy, M., Yu, Q. and Weijia, G., Microstructure, mechanical properties and wear behavior of Mg matrix composites reinforced with Ti and nano SiC particles, J. Mater. Res. Technol., 31, 4088–4103(2024).
https://doi.org/10.1016/j.jmrt.2024.07.125
Akash, D. B. N., Rajanna, S., Krishnamurthy, K. N., Manjunath, P. G. C., Ganesha, T., Reddy, G. V. G., Hasan, M. and Linul, E., Ultrasonic assisted stir squeeze casting of AA5456/Al2O3–SiC-Gr-MoS2 hybrid nanocomposites: Microstructure and strengthening analysis, J. Mater. Res. Technol., 34, 1611–1635(2025).
https://doi.org/10.1016/j.jmrt.2024.12.172
Akinwekomi, A. D., Microstructural characterisation and corrosion behaviour of microwave-sintered magnesium alloy AZ61/fly ash microspheres syntactic foams, Heliyon., 5(4), e01531(2019).
https://doi.org/10.1016/j.heliyon.2019.e01531
Ali, A., Rahimian, K. S. S., Alshehri, A. H. and Arockiarajan, A., Carbon nanotube characteristics and enhancement effects on the mechanical features of polymer-based materials and structures – A Review, J. Mater. Res. Technol., 24, 6495–6521(2023).
https://doi.org/10.1016/j.jmrt.2023.04.072
Alterary, S. S. and Marei, N. H., Fly ash properties, characterization, and applications: A review, J. King. Saud. Univ. Sci., 33(6), 101536(2021).
https://doi.org/10.1016/j.jksus.2021.101536
Anandaraj, S., Sakthi, S. S., Krishnaraja, A. R. and Mithun, T., Development of Green Engineered Cementitious Composite using Fly Ash and Nanosilica for 3D Printing, J. Environ. Nanotechnol., 13(1), 117–124(2024).
https://doi.org/10.13074/jent.2024.03.241515
Anbukarasi, K., Mala, D., Senthilkumar, N., Hussain, S. I. and Kalaiselvam, S., Investigation of TiO2 Nanoparticles Influence on Tensile Properties and Thermal Stability of Dry and Wet Luffa-Epoxy Nanocomposites, Recent. Pat. Nanotechnol., 19(4), 525–534(2025).
https://doi.org/10.2174/0118722105295445240418064351
Arora, G. S., Saxena, K. K., Mohammed, K. A., Prakash, C. and Dixit, S., Manufacturing Techniques for Mg-Based Metal Matrix Composite with Different Reinforcements, Cryst. (Basel)., 12(7), 945(2022).
https://doi.org/10.3390/cryst12070945
Ashby, M. F., Shercliff, H. and Cebon, D., Materials: Engineering, Science, Processing and Design, North American Edition, Butterworth-Heinemann (2013).
Aydın, F., Recent advances in mechanical properties of Mg matrix composites, A review, Mater. Sci. Technol., 40(5), 339–376(2024).
https://doi.org/10.1177/02670836241229025
Carou, D. and Davim, J.P., Machining of Light Alloys: Aluminum, Titanium, and Magnesium, 1st Ed., CRC Press (2018).
https://doi.org/10.1201/b22153
Chelladurai, S. J. S. and Jagadeeswaran, K., Evaluation of mechanical and wear properties of LM24/fly ash/titanium diboride hybrid metal matrix composites using stir casting, Part. Sci. Technol., 43(3), 338–356(2025).
https://doi.org/10.1080/02726351.2025.2456596
Dobrzanski, L. A., Bamberger, M. and Totten, G. E., Magnesium and Its Alloys, Technology and Applications, 1st Ed., CRC Press (2019).
https://doi.org/10.1201/9781351045476
Du, Z., Chen, H. C., Tan, M. J., Bi, G. and Chua, C. K., Effect of nAl2O3 on the part density and microstructure during the laser-based powder bed fusion of AlSi10Mg composite, Rapid. Prototyp. J., 26(4), 727–735(2020).
https://doi.org/10.1108/RPJ-05-2019-0136
Dziubinska, A., Surdacki, P. and Majerski, K., The Analysis of Deformability, Structure and Properties of AZ61 Cast Magnesium Alloy in a New Hammer Forging Process for Aircraft Mounts, Mater., 14(10), 2593(2021).
https://doi.org/10.3390/ma14102593
Elajjani, A., Feng, Y., Sun, C. and Feng, S., Development of constitutive relationship for thermomechanical processing of BN-reinforced magnesium composites to predict hot deformation behaviour, Mater. Technol., 40(1), 2471585(2025).
https://doi.org/10.1080/10667857.2025.2471585
El-Saeid, E. Y., Fernandez-Saez, J. and Perez-Castellanos, J. L, Some aspects of damage and failure mechanisms at high strain-rate and elevated temperatures of particulate magnesium matrix composites, Compos. B. Eng., 34(6), 551–560(2003).
https://doi.org/10.1016/S1359-8368(03)00046-5
Ferguson, J. B., Sheykh-Jaberi, F., Kim, C. S., Rohatgi, P. K. and Cho, K, On the strength and strain to failure in particle-reinforced magnesium metal-matrix nanocomposites (Mg MMNCs), Mater. Sci. Eng. A., 558, 193–204(2012).
https://doi.org/10.1016/j.msea.2012.07.111
Geng, R., Zhao, Q., Qiu, F. and Jiang, Q., Simultaneously increased strength and ductility via the hierarchically heterogeneous structure of Al-Mg-Si alloys/nanocomposite, Mater. Res. Lett., 8(6), 225–231(2020).
https://doi.org/10.1080/21663831.2020.1744759
Ghazanfari, S. M. H. and Zamanian, A., Phase transformation, microstructural and mechanical properties of hydroxyapatite/alumina nanocomposite scaffolds produced by freeze casting, Ceram. Int., 39(8), 9835–9844(2013).
https://doi.org/10.1016/j.ceramint.2013.05.096
Gnanavelbabu, A., Sunu, S. K. T. and Kumar, S., Influence of ultrasonication power on grain refinement, mechanical properties and wear behaviour of AZ91D/nano-Al2O3 composites, Mater. Res. Express., 7(1), 016544(2020).
https://doi.org/10.1088/2053-1591/ab64d7
Grilo, J., Carneiro, V. H., Teixeira, J. C. and Puga, H., Manufacturing Methodology on Casting-Based Aluminium Matrix Composites: Systematic review, Met., 11(3), 436(2021).
https://doi.org/10.3390/met11030436
Harshit, S., Vikas, S., Ashish, K. Y. And Ashok, K. T., Ultrafine GGBS and Fly Ash as Cement Replacement for Sustainable Concrete, J. Environ. Nanotechnol, 13(3), 25–30(2024).
https://doi.org/10.13074/jent.2024.09.242659
Isitan, A., Aytekin, S. and Onar, V., Enhancing the Microstructure and Mechanical Properties of Cast Aluminum Matrix Composites Through Nano-Al2O3 Reinforcement via CMT and PMC Welding, Int. J. Metalcast., 18(4), 3166–3179(2024).
https://doi.org/10.1007/s40962-023-01234-z
Ivanov, K. V., Fortuna, S. V., Kalashnikova, T. A. and Glazkova, E. A., The effect of geometric shape of Al2O3 nanoparticles on the nanoparticles distribution, microstructure and microhardness of Al-Al2O3 nanocomposite fabricated by accumulative roll bonding, AIP. Conf. Proc., 020109(2018).
https://doi.org/10.1063/1.5083352
Jones, F. R., Composites Science, Technology and Engineering, Cambridge. Univ. Press., (2022).
https://doi.org/10.1017/9781139565943
Kanth, U. R., Rao, P. S. and Krishna, M. G., Mechanical behaviour of fly ash/SiC particles reinforced Al-Zn alloy-based metal matrix composites fabricated by stir casting method, J. Mater. Res. Technol., 8(1), 737–744(2019).
https://doi.org/10.1016/j.jmrt.2018.06.003
Karakoc, H., Effect of SiC Particle Size on the Mechanical and Wear Behavior of Al356 Metal Matrix Composites, Silicon., 15(15), 6729–6744(2023).
https://doi.org/10.1007/s12633-023-02682-2
Khatkar, S. K., Hybrid magnesium matrix composites: A review of reinforcement philosophies, mechanical and tribological characteristics, Rev. Adv. Mater. Sci., 62(1), 20220294(2023).
https://doi.org/10.1515/rams-2022-0294
Kociubczyk, A. I., Grau, J. E., Sarutti, J. L., Mendez, C. M., Gregorutti, R. W. and Ares, A. E., Solidification Analysis, Microhardness, and Corrosion Resistance of a Cast Hip Prosthesis in ASTM F745 Austenitic Stainless Steel, J. Mater. Eng. Perform., 32(3), 1065–1075(2023).
https://doi.org/10.1007/s11665-022-07164-x
Kumar, D. and Thakur, L., Investigation on Mechanical and Wear Performance of Ultrasonic-Assisted Stir Cast AZ91D/Al2O3 Magnesium Matrix Composites, Met. Mater. Int., 29(9), 2767–2781(2023).
https://doi.org/10.1007/s12540-023-01395-w
Luo, Y. X., Dong, B. X., Yang, H. Y., Qiu, F., Yan, B. C., Shu, S. L., Jiang, Q. C. and Shi, F.J., Res. progress on nanoparticles reinforced magnesium alloys, J. Mater. Res. Technol., 30, 5166–5191(2024).
https://doi.org/10.1016/j.jmrt.2024.04.129.
Mohanty, A. and Srivastava, V. K., Effect of alumina nanoparticles on the enhancement of impact and flexural properties of the short glass/carbon fiber reinforced epoxy based composites, Fibers. Polym., 16(1), 188–195(2015).
https://doi.org/10.1007/s12221-015-0188-5
Muresan, L. M., Nanocomposite Coatings for Anti-Corrosion Properties of Metallic Substrates, Mater., 16(14), 5092(2023).
https://doi.org/10.3390/ma16145092
Nagarajan, B., Govindasamy, K., Chenrayan, V. and Shahapurkar, K., Tensile, Flexural, and Fatigue Responses of Lightweight Pumice-Reinforced Magnesium Composite: Experimentation Followed by an Analytical Modeling, J. Eng. Mater. Technol., 147(3), 1-13 (2025).
https://doi.org/10.1115/1.4067134
Narendran, J., Nagaraja, S., Karthikeyan, T., Anthoniraj, S. and Rudra, N. M., Evaluation, tribological examination, and multi‐objective optimization of aluminum‐fly ash egg shell composites for sustainability, Eng. Rep., 6(12), e12980(2024).
https://doi.org/10.1002/eng2.12980
Nie, K. B., Wang, X. J., Deng, K. K., Hu, X. S. and Wu, K., Magnesium matrix composite reinforced by nanoparticles – A Review, J. Magnesium. Alloys., 9(1), 57–77(2021).
https://doi.org/10.1016/j.jma.2020.08.018
Ostolaza, M., Arrizubieta, J. I., Lamikiz, A. and Ukar, E., Study of the flexural behaviour and bonding strength of WC-Co metal matrix composite coatings produced by Laser Directed Energy Deposition, Surf. Coat. Technol., 463, 129538(2023).
https://doi.org/10.1016/j.surfcoat.2023.129538
Osunmakinde, L., Asafa, T. B., Agboola, P. O. and Durowoju, M. O., A Systemic review. of the influence of eco-friendly particles on hybrid composites synthesized via stir casting technique, Discover. Mech. Eng., 3(1), 32(2024).
https://doi.org/10.1007/s44245-024-00055-6
Pandian, R. and Vinayagam, M., Impacts of Zirconium Carbide Incorporated Magnesium Alloy Nanocomposite on Wear Properties, J. Environ. Nanotechnol., 13(3), 217–221(2024).
https://doi.org/10.13074/jent.2024.09.243837
Ren, J. Y., Ji, G. C., Guo, H. R., Zhou, Y. M., Tan, X., Zheng, W. F., Xing, Q., Zhang, J. Y., Sun, J. R., Yang, H. Y., Qiu, F. and Jiang, Q. C., Nano-Enhanced Phase Reinforced Magnesium Matrix Composites: A review of the Matrix, Reinforcement, Interface Design, Properties and Potential Applications, Mater., 17(10), 2454(2024).
https://doi.org/10.3390/ma17102454
Sagar, P., Khanna, S. K., Vignjevic, R. and Handa, A., Synergistic effect of hybrid reinforcement on magnesium-based composites for enriching mechanical and tribological characteristics, Proc. Inst. Mech. Eng., Part E: J. Process. Mech. Eng., (2024).
https://doi.org/10.1177/09544089231221683
Saleh, B., Fathi, R., Zhang, L., Yu, Z., Liu, S. and Zhao, L., Enhancing mechanical and wear performances of magnesium matrix composites using low-cost squid quill ash, Compos. B. Eng., 277, 111383(2024).
https://doi.org/10.1016/j.compositesb.2024.111383
Samvatsar, K. and Dave, H., A comprehensive study on using fly ash as reinforcement material in aluminium and magnesium based syntactic foams, Mater. Today. Proc., 47, 2384–2390(2021).
https://doi.org/10.1016/j.matpr.2021.04.353
Saranu, R. K., Chanamala, R., Putti, S. R. and Mallarapu, G. K., Investigation of Microstructures, Mechanical Properties of AZ91E Hybrid Composite Reinforced with Silicon Carbide and Fly Ash, Silicon., 13(7), 2145–2156(2021).
https://doi.org/10.1007/s12633-020-00671-3
Senthilkumar, N., Perumal, G., Palanikumar, K., Deepanraj, B. and Basha, M. S., Wear and mechanical characteristics of coated Ti-6Al-4 V alloy with an alumina-13 wt.% titania -40 wt.% yitrium stabilized zirconia ceramic composite via plasma spraying technique, Results. Eng., 25, 103777(2025).
https://doi.org/10.1016/j.rineng.2024.103777
Shahabaz, S. M., Mehrotra, P., Kalita, H., Sharma, S., Naik, N., Noronha, D. J. and Shetty, N., Effect of Al2O3 and SiC Nano-Fillers on the Mechanical Properties of Carbon Fiber-Reinforced Epoxy Hybrid Composites, J. Compos. Sci., 7(4), 133(2023).
https://doi.org/10.3390/jcs7040133
Shishehbor, M., Sakaniwa, D., Stefaniuk, D., Krakowiak, K. J. and Abdolhosseini, Q. M. J., On the significance of interfacial chemistry on the strength of fly ash-cement composites, Cem. Concr. Res., 151, 106619(2022).
https://doi.org/10.1016/j.cemconres.2021.106619
Singhal, V., Shelly, D., Saxena, A., Gupta, R., Verma, V. K. and Jain, A., Study of the Influence of Nanoparticle Reinforcement on the Mechanical and Tribological Performance of Aluminum Matrix Composites—A Review, Lubr., 13(2), 93(2025).
https://doi.org/10.3390/lubricants13020093
Sudarsan, D., Bovas, H. B, A., Raj, K. S., Anitha, A. S. and Venkat, P. S., Evaluation of the Mechanical Properties of Aluminium Hybrid Nano Composites Using Ultrasonic-Assisted Stir Casting Method and Reinforced with Nano-scale SiC and MoS2 Particles, J. Environ. Nanotechnol., 13(3), 282–288(2024).
https://doi.org/10.13074/jent.2024.09.242665
Surendran, S. K. and Gnanavelbabu, A., Tribological performance of AZ91D/HfC p magnesium composite prepared through stir-ultrasonic-squeeze casting technique, Proceedings of the Institution of Mechanical Engineers, Part E: J. Process. Mech. Eng., 09544089221132732 (2022).
https://doi.org/10.1177/09544089221132732
Titarmare, V. P., Banerjee, S. and Sahoo, P., Ultrasonic-Assisted Stir Casting Synthesis and Characterization of Magnesium Metal Matrix Composites, Adv. Mater. Manuf. Des., 55–67(2025).
https://doi.org/10.1007/978-981-97-6667-3_5
Uday, K. and Rajamurugan, G., Effect of stir casting parameters and mono/hybrid reinforcements on aluminium metal matrix composite–A review, J. Mech. Eng. Sci., 236(9), 4904–4920(2022).
https://doi.org/10.1177/09544062211052166
Virendra, K. Y., Nisha, C., Pankaj, K. and Fulekar, M. H., Synthesis and Characterization of Iron Oxide Nanoparticles from Coal Fly Ash Waste and their Application for the Removal of Methyl Red Dye from Aqueous Solutions, J. Environ. Nanotechnol., 13(4), 47–55(2024).
https://doi.org/10.13074/jent.2024.12.243926
Wei, Y., Chai, J., Qin, Y., Li, Y., Xu, Z., Li, Y. and Ma, Y., Effect of fly ash on mechanical properties and microstructure of cellulose fiber-reinforced concrete under sulfate dry–wet cycle attack, Constr. Build. Mater., 302, 124207(2021).
