Epoxy Coatings at Cryogenic Temperatures with and without Nano-fillers – A Review
J. Environ. Nanotechnol., Volume 14, No 2 (June 2025) pp. 352-362
Abstract
The study of cryogenic coatings has garnered substantial interest from engineers due to their wide range of applications, particularly in the aerospace and chemical industries. Polymers with their advantages of good mechanical properties and low weight are being considered for coating on both metallic and non-metallic substrates working at different ranges of temperatures, from high to very low temperatures. Very low temperatures, usually below -150°C to absolute zero, are termed cryogenic temperatures. This report compiles the studies on the tribological and mechanical properties of polymer coatings developed for cryogenic environments. The primary focus is on the epoxy resin (DGEBA) and its enhanced variants incorporating additives like graphene nanoplatelets (GNP), graphene and carbon nanotubes (CNT).
Full Text
Reference
Acikbas, G., Sezer K., Özcan, S. and Calis, A. N., The effect of hydrophobic coating applied to mica reinforced epoxy matrix composites on the water absorption properties of the composite, Polym. Bull., 81(7), 6207-24 (2024). https://doi.org/10.1007/s00289-023-04680-0
Bahrami, M., Ranjbar Z., Khosroshahi, R. A. and Ashhari, S., Investigating corrosion protection properties of epoxy thermal insulators through cyclic corrosion test, Prog. Org. Coat., 113, 25-30 (2017). https://doi.org/10.1016/j.porgcoat.2017.07.021
Beaugendre, A., Lemesle, C., Bellayer S., Degoutin, S., Duquesne, S., Casetta, M., Pierlot, C., Jaime, F., Kim, T., Jimenez, M., Flame retardant and weathering resistant self-layering epoxy-silicone coatings for plastics, Prog. Org. Coat., 136, 105269 (2019). https://doi.org/10.1016/j.porgcoat.2019.105269
Berto, F. and Lazzarin, P., Recent developments in brittle and quasi-brittle failure assessment of engineering materials by means of local approaches, Mater. Sci. Eng. Rep., 75, 1-48 (2014).
https://doi.org/10.1016/j.mser.2013.11.001
Chen, C., Qiu, S., Cui, M., Qin, S., Yan, G., Zhao, H., Wang, L., Xue, Q., Achieving high-performance corrosion and wear-resistant epoxy coatings via incorporation of noncovalent functionalized graphene, Carbon N. Y., 114, 356–366 (2017).
https://doi.org/10.1016/j.carbon.2016.12.044
Chen, D., Li, J., Yuan, Y., Gao, C., Cui, Y., Li, S., Liu, X., Wang, H., Peng, C. and Wu, Z., A review of the polymer for cryogenic application: methods, mechanisms and perspectives, Polymers, 13(3), 320(2021).
https://doi.org/10.3390/polym13030320
Chen, Z. K., Yang, J. P., Ni, Q. Q., Fu, S. Y., Huang, Y. G., Reinforcement of epoxy resins with multi-walled carbon nanotubes for enhancing cryogenic mechanical properties, Polymer, 50, 4753–4759 (2009).
https://doi.org/10.1016/j.polymer.2009.08.001
Chhipa, S. M., Sharma, S. and Bagha, A. K., Recent development in polymer coating to prevent corrosion in metals: A review, Mater. Today Proc., (2024).
https://doi.org/10.1016/j.matpr.2024.09.001
Cui, Y., Yan, J., Li, J., Chen, D., Wang, Z., Yin, W. and Wu, Z., Cryogenic Mechanical Properties and Stability of Polymer Films for Liquid Oxygen Hoses, Polym., 15(16), 3423 (2023).
https://doi.org/10.3390/polym15163423
Deenoi, S. and Dechjarern, S., Effect of cryogenic and coating treatments on wear and friction between titanium alloy and UHMWPE for knee implants, Mater. Today Proc., 17, 1939-1948 (2019).
https://doi.org/10.1016/j.matpr.2019.06.237
Deyab, M. A., El-Bali, B., Mohsen, Q., Essehli, R., Design new epoxy nanocomposite coatings based on metal vanadium oxy-phosphate M0. 5VOPO4 for anti-corrosion applications, Sci. Rep., 11(1): 8182 (2021).
https://doi.org/10.1038/s41598-021-87637-5
Dhole, G. S., Gunasekaran, G., Naik, R., Ghorpade, T., Vinjamur, M., Fluorescence based corrosion detecting epoxy coating, Prog. Org. Coat., 138, 105425 (2020).
https://doi.org/10.1016/j.porgcoat.2019.105425
El-Sherif, H. M., Nasser, A. M., Hussin, A. I., Abd El-Wahab, H., Ghazy, M. B. M., Elsayed, A. E., Nano emulsion binders for paper coating synthesis and application, J. Macromolecul. Sci. Part A., 54(5), 271–287 (2017).
https://doi.org/10.1080/10601325.2017.1294450
Fan, J., Yang, J., Li, H., Tian, J., Wang, M. and Zhao, Y., Cryogenic mechanical properties of graphene oxide/epoxy nanocomposites: Influence of graphene oxide with different oxidation degrees, Polym. Test., 96, 107074 (2021).
https://doi.org/10.1016/j.polymertesting.2021.107074
Ferrick, M. G., Mulherin, N. D., Haehnel, R. B., Coutermarsh, B. A., Durell, G. D., Tantillo, T. J., Curtis, L. A., Clair, T. S., Weiser, E. S., Cano, R. J. and Smith, T. M., Evaluation of ice release coatings at cryogenic temperature for the space shuttle, Cold Reg. Sci. Technol., (52)2, 224-243 (2008).
https://doi.org/10.1016/j.coldregions.2007.03.002
Ganni, V. and Fesmire, J., Cryogenics for superconductors: Refrigeration, delivery, and preservation of the cold, AIP Conference Proceedings, 1434(1), 15-27 (2012).
https://doi.org/10.1063/1.4706901
Goffin, B., Banthia, N. and Yonemitsu, N., Use of infrared thermal imaging to detect corrosion of epoxy coated and uncoated rebar in concrete, Constr. Build. Mater., 263, 120162 (2020).
https://doi.org/10.1016/j.conbuildmat.2020.120162
Gravit, M., Klementev, B. and Shabunina, D., Fire protection of steel structures with epoxy coatings under cryogenic exposure, Buildings, 11(11), 53 (2021).
https://doi.org/10.3390/buildings11110537
Han, C. C., Zhao, J., Wei, Y., Sung, L. P., Gu, X., Clerici, C., Dispersion of particles in the coatings characterized by laser scanning confocal microscopy (LSCM) I: Vertical dispersion of particles in the coatings and the weathering property studied by orthogonal analysis method of LSCM, Sci. China Technol. Sci., 53, 2247-51 (2010).
https://doi.org/10.1007/s11431-010-4085-0
Hall, D. B., Underhill, P., Torkelson, J. M. Spin coating of thin and ultrathin polymer films, Polym. Engineer. Sci., 38(12), 2039–2045 (1998).
https://doi.org/10.1002/pen.10373
He, Y., Chen, Q., Yang, S., Lu, C., Feng, M., Jiang, Y., Cao, G., Zhang, J. and Liu, C., Micro-crack behavior of carbon fiber reinforced Fe₃O₄/graphene oxide modified epoxy composites for cryogenic application. Compos, Part A Appl. Sci. Manuf., 108, 12-22 (2018).
https://doi.org/10.1016/j.compositesa.2018.02.014
Huang, Y. K. P. H. Frings, and E. Hennes, Mechanical properties of Zylon/epoxy composite, Compos B Eng., 33(2), 109-115 (2002).
https://doi.org/10.1016/S1359-8368(01)00064-6
Hughes, A. E., Mayo, S., Yang, Y. S., Markley, T., Smith, S. V., Sellaiyan, S., Uedono, A., Hardin, S. G., Muster, T. H., Using X-ray tomography, PALS and Raman spectroscopy for characterization of inhibitors in epoxy coatings, Prog. Org. Coat., 74(4), 726-33(2012).
https://doi.org/10.1016/j.porgcoat.2011.06.023
Ichetaonye, S., Production of Domestic Utensils Using Waste Polyethylene Terephthalate (PET) Bottle Caps Without the Aid of Industrial Machines, Preprint, (2023).
https://doi.org/10.21203/rs.3.rs-2905442/v1
Jakab, B., Panaitescu, I. and Gamsjäger, N., The action of fillers in the enhancement of the tribological performance of epoxy composite coatings, Polym. Test., 100, 107243 (2021).
Jha, A. R, Cryogenic Technology and Applications, Butterworth-Heinemann, (2006).
https://doi.org/10.1016/B978-0-7506-7887-2.X5000-X
Jiang, Y., Liu, Y., Gong, J., Li, C., Xi, Z., Cai, J. and Xie, H., Microstructures, thermal and mechanical properties of epoxy asphalt binder modified by SBS containing various styrene-butadiene structures, Mater. Struct., 51, 1-13 (2018).
https://doi.org/10.1617/s11527-018-1217-9
Jin, R., Zhang, Y., Guo, D., Zhou, Z., Qu, L. and Xu, B., New flexible 3D POSS-based COF simultaneously strengthens and toughens epoxy resin (EP) at extreme temperatures, Compos, Part A Appl. Sci. Manuf., 193, 108846 (2025).
https://doi.org/10.1016/j.compositesa.2025.108846
Joung, J., The Kendall Company, Polymer coating and curing process for catheters, U.S. Patent 4,318,947 (1982).
Kamde, D. K., Pillai, R. G., Effect of sunlight/ultraviolet exposure on the corrosion of fusion-bonded epoxy (FBE) coated steel rebars in concrete, Corrosion, 76(9), 843-60 (2020).
Kambhampati. S., Cao, Q., Ghodkay, V., Farhat, H., Pojtanabuntoeng, T., A Systematic Study on the Effects of Key Influencing Factors on a Pull-Off Adhesion Test of Organic Coatings, Corrosion, 79(6), 683-91(2023).
Khan, A., Savi, P., Quaranta, S., Rovere, M., Giorcelli, M., Tagliaferro, A., Rosso, C. and Jia, C. Q. Low-cost carbon fillers to improve mechanical properties and conductivity of epoxy composites, Polym., 9(12), 642 (2017).
https://doi.org/10.3390/polym9120642
Khun, N. W., Troconis, B. C. R., Frankel, G. S. Effects of carbon nanotube content on adhesion strength and wear and corrosion resistance of epoxy composite coatings on AA2024-T3, Prog. Org. Coat., 77, 72–80 (2014).
https://doi.org/10.1016/j.porgcoat.2013.08.003
Kiattipornpithak, K., Thajai, N., Kanthiya, T., Rachtanapun, P., Leksawasdi, N., Phimolsiripol, Y., Rohindra, D., Ruksiriwanich, W., Sommano, S. R., Jantanasakulwong, K., Reaction mechanism and mechanical property improvement of poly (lactic acid) reactive blending with epoxy resin, Polym., 13(15), 2429 (2021).
https://doi.org/10.3390/polym13152429
Kim, J., Im, H., Cho, M. H. Tribological performance of fluorinated polyimide-based nanocomposite coatings reinforced with PMMA-grafted-MWCNT, Wear, 271, 1029–1038 (2011).
https://doi.org/10.1016/j.wear.2011.03.015
Kimoto, Y., Kanamori, K., Yonezu, A., Yamada, H., Adhesion Strength of Al/Epoxy Resin Interface over a Wide Range of Loading Rates, EPJ Web of Conferences 250:01003 EDP Sciences (2023).
https://doi.org/10.1051/epjconf/202125001003
Lan, P., Gheisari, R., Meyer, J.L. and Polycarpou, A.A., Tribological performance of aromatic thermosetting polyester (ATSP) coatings under cryogenic conditions, Wear, 398, 47-55 (2018).
https://doi.org/10.1016/j.wear.2017.12.007
Le, H. R., Howson, A., Ramanauskas, M., Williams, J. A., Tribological characterization of air-sprayed epoxy-CNT nanocomposite coatings, Tribol. Lett., 45, 301–308 (2012).
https://doi.org/10.1007/s11249-011-9889-0
Liddell, H. P, Erickson L.M., Tagert, J. P., Arcari, A., Smith, G. M., Martin, J., Mode mixity and fracture in pull-off adhesion tests, Eng. Fract. Mech., 281, 109120 (2023).
https://doi.org/10.1016/j.engfracmech.2023.109120
Li, H., Feng, B., Xu, Y., Zhong, J., Impact resistance capacity and degradation law of epoxy-coated steel strand under the impact load, Sci. Eng. Compos. Mater., 30(1), 20220190 (2023).
https://doi.org/10.1515/secm-2022-0190
Li, Y., He, H., Ma, Y., Geng, Y. and Tan, J., Rheological and mechanical properties of ultrahigh molecular weight polyethylene/high density polyethylene/polyethylene glycol blends, Adv. Ind. Eng. Polym. Res., 2(1), 51-60 (2019).
https://doi.org/ 10.1016/j.aiepr.2018.08.004
Liu, D., Zhao, W., Wu, F., Cen, Q., Zeng, Z., Wu, X., Xue, Q., Effect of curing agent molecular structures on epoxy resin coatings' tribological and corrosion behaviors, Colloids Surf. A Physicochem. Eng. Asp., 472, 85–91(2015).
https://doi.org/10.1016/j.colsurfa.2015.02.036
Liu, D., Zhao, W., Liu, S., Cen, Q., Xue, Q., Comparative tribological and corrosion resistance properties of epoxy composite coatings reinforced with functionalized fullerene C₆₀ and graphene, Surf. Coat. Technol., 286, 354–364, (2016).
https://doi.org/10.1016/j.surfcoat.2015.12.056
Liu, L., Xiao, J. and Wu, Z., The effect of fibre content on the static and dynamic performance of PE-ECC, Case Stud. Constr. Mat., 20, e03041 (2024).
https://doi.org/10.1016/j.cscm.2024.e03041
Liu, N., Ma, B., Liu, F., Huang, W., Xu, B., Qu, L. and Yang, Y., Progress in research on composite cryogenic propellant tank for large aerospace vehicles, Compos, Part A Appl. Sci. Manuf., 143, 106297 (2021).
https://doi.org/10.1016/j.compositesa.2021.106297
Lu, Y., Ganguli, R., Drewien, C. A., Anderson, M. T., Continuous formation of supported cubic and hexagonal mesoporous films by sol-gel dip-coating, Nature, 389(6649), 364 (1997).
MacQueen, R. C. and Granata, R. D., A positron annihilation lifetime spectroscopic study of the corrosion protective properties of epoxy coatings, Prog. Org. Coat., 28(2), 97-112 (1996).
https://doi.org/10.1016/0300-9440(95)00557-9
Madhav, H., Singh, N. and Jaiswar, G., Thermoset, bioactive, metal–polymer composites for medical applications, Biomed. Mater., Elsevier, 105-143 (2019).
https://doi.org/10.1016/B978-0-12-816874-5.00004-9
Mahmoudi, F., Abdalla, J.A., Hawileh, R. A. and Zhang, Z., Tensile and compressive strength of polyethylene engineered cementitious composite (PE-ECC) at elevated temperature, Mater. Today Proc. , 65, 2081-2085 (2022).
https://doi.org/10.1016/j.matpr.2022.06.451
Marrivada, G. V., Chaganti, P. K., Sujith, R. and Sharma, B., Effect of addition of graphene nanoplatelets on the mechanical properties of triaxially braided composites, Adv. Compos. Mater., 32(2), 182–210 (2022).
https://doi.org/10.1080/09243046.2022.2080990
Marrivada, G. V., Chaganti, P. K., Sujith, R., Experimental investigation and machine learning prediction of mechanical properties of graphene nanoplatelets-based triaxial braided composites, Mater. Today Commun., 34, 105305 (2023).
https://doi.org/10.1016/j.mtcomm.2022.105305
Molero, G., Sue, H. J., Scratch behavior of model epoxy resins with different crosslinking densities, Mater. Des., 182, 107965 (2019).
https://doi.org/10.1016/j.matdes.2019.107965
Muhammad A. N. S., Farooq A., Lodhi M., Deen K., Performance evaluation of epoxy coatings containing different fillers in natural and simulated environmental conditions for corrosion resistance, J. Biomed. Eng. Biosci., 3(4), 338-344(2019).
https://doi.org/10.32474/OAJBEB.2019.03.000168.
Ojha, M., Penumakala, P. K., Marrivada, G. V., Chaganti, P. K., Gupta, A. K., Processing of glass fiber pultruded composites using graphene nanoplatelets modified epoxy matrix, Mater. Today Proc., 18, 3298-3304 (2019).
https://doi.org/10.1016/j.matpr.2019.07.287
Oyeniran, C. O., Adewusi, A. O., Adeleke, A. G., Akwawa, L. A. and Azubuko, C. F., Advancements in quantum computing and their implications for software development, CSITR J., 4(3), 577-593 (2023).
https://doi.org/10.51594/csitrj.v4i3.1558
Park, S. J. and Seo, M. K., Element and processing, Interface Sci. Technol., 18, 431-499 (2011).
https://doi.org/10.1016/B978-0-12-375049-5.00006-2
Parra D. F, Mercuri L. P, Matos J. D, Brito H. F, Romano R. R., Thermal behavior of the epoxy and polyester powder coatings using thermogravimetry/differential thermal analysis coupled gas chromatography/mass spectrometry (TG/DTA–GC/MS) technique: identification of the degradation products, Thermo chimica Acta., 386(2), 143-51 (2002).
https://doi.org/10.1016/S0040-6031(01)00737-1
Pulikkalparambil, H., Siengchin, S., Parameswaranpillai, J., Corrosion protective self-healing epoxy resin coatings based on inhibitor and polymeric healing agents encapsulated in organic and inorganic micro and nanocontainers, Nano Struct. Nano Objects, 16, 381–395 (2018).
https://doi.org/10.1016/j.nanoso.2018.09.010
Ren, Y., Song, H., Cai, Q., Cai, Z., Liu, Y. and Wang, B., Modeling analysis and experimental study on epoxy packaged FBG sensor for cryogenic temperature measurement, Opt. Fiber Technol., 84: 103710 (2024).
https://doi.org/10.1016/j.yofte.2024.103710
Rubinsky, B. Cryosurgery. Annu. Rev. Biomed. Eng., 2(1), 157-187(2000).
https://doi.org/10.1146/annurev.bioeng.2.1.157
Sabau, A. S, Jun, J, McClurg, D, Coating adhesion of a chromate-containing epoxy primer on Al2024-T3 surface processed by laser-interference, Int. J. Adhes., 102, 102641 (2020).
https://doi.org/10.1016/j.ijadhadh.2020.102641
Sampath, U., Kim, D., Kim, H. and Song, M., Polymer-coated FBG sensor for simultaneous temperature and strain monitoring in composite materials under cryogenic conditions, Appl. Opt., 57(3), 492-497 (2018).
https://doi.org/10.1364/AO.57.000492
Sampath, U. and Song, M., Epoxy-Coated Side-Polished Fiber-Optic Temperature Sensor for Cryogenic Conditions, Sensors, 23(5), 2850 (2023).
https://doi.org/10.3390/s23052850
Sethi, S. and Ray, B. C., Mechanical behavior of polymer composites at cryogenic temperatures, Polymers at Cryogenic Temperature, 59-113 (2013).
https://doi.org/10.1007/978-3-642-35335-2_4
Sápi, Zsombor, and Richard Butler., Properties of cryogenic and low temperature composite materials–A review, Cryogenics, 111, 103190 (2020).
https://doi.org/10.1016/j.cryogenics.2020.103190
Sapinski, P., Szczepaniak, R., Plonka, D., Krzyzak, A., Kosicka, E., Woroniak, G., Determination of Heat Deflection Temperature under a Load and Vicat Softening Temperature of Powder Composites used for Ablative Shields, Acta Mechanica et Automatica., 18(4), (2024).
https://doi.org/10.2478/ama-2024-0077
Shen, X. J., Liu, Y., Xiao, H. M., Feng, Q. P., Yu, Z. Z., Fu, S. Y., The reinforcing effect of graphene nanosheets on the cryogenic mechanical properties of epoxy resins, Compos. Sci. Technol., 72, 1581–1587 (2012).
https://doi.org/10.1016/j.compscitech.2012.06.021
Sienkiewicz, N., Dominic, M. and Parameswaranpillai, J., Natural fillers as potential modifying agents for epoxy composition: A review, Polym.,14(2), 265 (2022).
https://doi.org/10.3390/polym14020265
Sma, I., Ünaldi, S., Ayad, M., Gervais, M., Berthe, L., Richaud, E., Laser shock adhesion testing of thermally aged epoxy coatings, Prog. Org. Coat., 195, 108603 (2024).
https://doi.org/10.1016/j.porgcoat.2024.108603
Studer, P. B., Alain S., and Theo, A. T., Tough epoxy resin systems for cryogenic applications, Cryogenics, 143, 103923 (2024).
https://doi.org/10.1016/j.cryogenics.2024.103923
Sung, L. P., Jasmin, J., Gu, X., Nguyen, T., Martin, J. W, Use of laser scanning confocal microscopy for characterizing changes in film thickness and local surface morphology of UV-exposed polymer coatings, JCT Research, 1, 267-76 (2004).
https://doi.org/10.1007/s11998-004-0005-6
Susanna, G., Salamandra, L., Brown, T. M., Di Carlo, A., Brunetti, F., Reale, A., Airbrush spray-coating of polymer bulk-heterojunction solar cells, Sol. Energy Mater. Sol. Cell., 95(7), 1775–1778 (2011).
https://doi.org/10.1016/j.solmat.2011.01.020
Singh, K. P., Singh, A., Kumar, N. and Tripathi, D .N., Morphological features, dielectric and thermal properties of epoxy–copper cobaltite nanocomposites: preparation and characterization, Bull. Mater. Sci., 43(1), 114 (2020).
https://doi.org/10.1007/s12034-020-02092-9
Turri, S., Torlaj, L., Piccinini, F., Levi, M., Abrasion and nanoscratch in nanostructured epoxy coatings, J. Appl. Polym. Sci., 118(3), 1720-7 (2010).
https://doi.org/10.1002/app.32309
Vandi, L. J., Truss, R., Veidt, M., Rasch, R., Heitzmann, M. T., Paton, R., Fluorine mobility during SEM-EDX analysis: a challenge for characterizing epoxy/fluoropolymer interfaces, J. Phys. Chem. C., 117(33), 16933-41 (2013).
https://doi.org/10.1021/jp4045952
Wang, B., Wilkes, G. L., Novel hybrid inorganic-organic abrasion-resistant coatings prepared by a sol-gel process, J. Macromolecul. Sci. Part A, 31(2), 249–260 (1994).
https://doi.org/10.1080/10601329409349731
Wang, J., Gong, J., Gong, Z., Yan, X., Wang, B., Wu, Q., Li, S., Effect of curing agent polarity on water absorption and free volume in epoxy resin studied by PALS, Nucl. Instrum. Methods Phys. Res., Sect. B, 268(14), 2355-61(2010).
https://doi.org/10.1016/j.nimb.2010.04.010
Wang, J., Wang, Z., Liu, R., Xiao, R., Li, Q., Study on adhesion reliability and particle inhibition of epoxy resin coating in DC GIL after thermal ageing experiment, Coatings, 12(6), 858 (2022).
https://doi.org/10.3390/coatings12060858
Wang, X., Cao, Q., Tang, F., Pan, H., Chen, X., & Lin, Z., Mechanical Properties and Corrosion Behavior of Dual-Filler-Epoxy-Coated Steel Rebar under a Corrosive Environment, Coatings, 13(3), 604 (2023).
https://doi.org/10.3390/coatings13030604
Wei, H., Xia, J., Zhou, W., Zhou, L., Hussain G., Li, Q., Ostrikov, K. K., Adhesion and cohesion of epoxy-based industrial composite coatings, Compos B Eng., 193, 108035 (2020).
https://doi.org/10.1016/j.compositesb.2020.108035
Weisend, J., G., Handbook of Cryogenic Engineering. Philadelphia, Taylor and Francis, (1998).
https://doi.org/10.1201/9781482277666
Yan, X., Wu, L., Jin, S., Zhao, W., Cao, H., Ma, Y., Effect of curing conditions on the cutting resistance of fabrics coated with inorganic-powder-reinforced epoxy composite, RSC Adv., 10(55), 33576-84(2020).
https://doi.org/10.1039/D0RA05196A
Yan, Z., Liu, W., Gao, N., Wang, H., Su, K., Synthesis and properties of a novel UV-cured fluorinated siloxane graft copolymer for improved surface, dielectric and tribological properties of epoxy acrylate coating, Appl. Surf. Sci., 284, 683–691 (2013).
https://doi.org/10.1016/j.apsusc.2013.07.156
Zargarnezhad, H., Wong, D., Lam, C. C., Asselin E., Uniform and local degradation of epoxy-based powder coatings: Salt transport and accelerated exposure analysis, J. Pipeline Sci. Eng., 4(4), 100197 (2024).
https://doi.org10.1016/j.jpse.2024.100197
Zhang, J., Kong, G., Li, S., Le, Y., Che, C., Zhang, S., Lai, D. and Liao, X., Graphene-reinforced epoxy powder coating to achieve high-performance wear and corrosion resistance, JMR&T, 20, 4148-4160(2022).
https://doi.org/10.1016/j.jmrt.2022.08.156
Zhang, R., Wang, H., Wang, X., Guan, J., Li, M., Chen, Y., Rubber-composite-nanoparticle-modified epoxy powder coatings with low curing temperature and high toughness, Polym., 15(1), 195 (2022).
https://doi.org/10.3390/polym15010195
Zohuri, B., Physics of Cryogenics. Heat Exchangers, 12th Ed., University of New Mexico, 12, 299-330 (2018).
